PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Seat Toledo (98-04) Pressed Arm – Front Poly Wishbone/ ARB Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Seat Leon Cupra R MK1 (99-05) Pressed Arm – Front Poly Wishbone/ ARB Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Audi A3 (96-03) Pressed Arm – Front Wishbone with ARB Polyurethane Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Audi S3 (99-03) Pressed Arm – Front Wishbone with ARB Polyurethane Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Audi TT MK1 (98-06) Front Wishbone with ARB Polyurethane Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x Skoda Octavia MK1 (96-04) Pressed Arm – Front Wishbone with ARB Polyurethane Bushing Kit appeared first on psbushings.co.uk.

PSB specializes in manufacturing polyurethane “problem solving bushings”. We strive to develop new and innovative products that are not just factory replacement parts, but actually solve many complex and inherent design problems in new vehicle suspensions.

Two Reasons Our Bushings Are Successful:

Design – The sleeves in our bushings freely rotate which enhances longevity.

Installation – Once removal of original bushings has taken place, installation of the new polyurethane bush typically takes from 1 – 5 minutes to install, the techs love it!

Why use Polyurethane?

Polyurethane bushings are stronger and last longer than standard rubber bushings. Most modern production vehicles are designed using rubber bushings which have a limited lifespan. This contributes to suspension failure due to vehicular weight and the inherent design of high-tech suspensions. Typically this results in less than desirable vehicle handling and can cause many related parts to wear out more rapidly than necessary. Polyurethane corrects this problem and in many cases improves vehicle handling and drivability.

–       This product is manufactured with the highest grade of polyurethane and the durometer of the bushing is designed to fit the application.

–       The quality and lifespan of this product far exceeds the original part.

–       If this product does not meet with your expectations, we will refund the purchase price if returned within two weeks after the purchase date.

Installation Instructions:

Front Wishbone Arm Front Bush 30mm OD – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Remove metal sleve from new poly bushing.

5. Lubricate inside and outside of poly bushing with a multi-purpose grease.

6. Press two bushing valves into housing. (rubber hammer or by hand)

7. Insert metal sleeve into bushings.

8. The installation is complete.

Front Wishbone Arm Rear Bush – Pressed Arm.
1. Remove original bushing by pressing out or using a blow torch.

2. Ensure outer metal casing of original rubber bushing is removed, which can be done by cutting with a hacksaw and knocking out with a chisel.

3. Clean housing with sand paper to remove sharp edges, so not to damage new bushing.

4. Lubricate the inside of the outer bushing.

5. Tap outer bushing into the housing from the top of the arm with a rubber mallet.

6. Tap inner bushing inside the outer bushing from the underside of the arm. (Do not attempt to remove the metal sleeve from the inner bushing)

7. The installation is complete.

The post 6x VW Beetle (97-11) Front Wishbone with ARB Polyurethane Bushing Kit appeared first on psbushings.co.uk.